Showing posts with label Blunami. Show all posts
Showing posts with label Blunami. Show all posts

Tuesday, November 11, 2025

Blunami! Pt 3

I said I was going to show the installation on a Bachmann J class, but I got into a bind and didn't have the time to take any pictures. I also installed one in another ATSF 4-8-4, and the only thing different about it from the previous installations that I have already shown is the size of the decoder, which I will show later in this post.

I had one of the old type Bachmann J classes that I was trying to get running for a friend, and he was considering putting a decoder in it if I could get it to run decently. It had the dreaded split gears, and I had found some 3D printed gears, but the old chassis just doesn't run well. I told him that I could put a decoder in the old crappy B-Mann chassis J, but it would never be a great runner. I might possibly get it to be an adequate runner, but given the limitations of that chassis that was about as good as it was going to get.

However, there was a guy selling one for a really really good price, and I bought it. I told my friend that I would pass it on to him for the same price as I paid for it, and I could try to work with the old one but the new one is miles and miles superior to the old one and for the price he would be an idiot not to go that route instead. Of course he agreed with me.

It was supposed to have an ESU decoder, and it did, but when it got to me I found the tender top had a hole cut in it for the cube speaker and the speaker sounded like garbage. So, I ordered a new tender shell and some speakers of the correct round type for the loco and traded him that one for one that I had on hand that had a Tsunami 2 TSU-1100 installed in it. 

This was a loco that I had picked up really cheap at a train show (cheaper than the "new" one that had just arrived, in fact) because it didn't run (a bit of Kapton tape on the chassis fixed it right up). I traded shells on the locos (my old one was 601 and the new one was 611, which is the one he wanted) and waited for my parts to come in.

When the tender shell and speakers arrived it was quick work to swap them out. Bachmann really hit it out of the park with the Spectrum J class locos built after 2005, and installing a sound decoder consists of removing the tender shell, removing the PC board just enough to slip the 15mm round speaker into the pocket made for it, reinstalling the PC board, and soldering the decoder in to the tabs built on the PC board for just that purpose.

Of course for this one I had to remove the old speaker and ECU decoder first, but once that was done and the old solder removed from the board the new installation went as expected. As I mentioned before, while I was at it I installed a Blunami BLU-1100 in the last of the three 4-8-4's I have, too, so now I have four 4-8-4 locos (three ATSF and one J class) equipped with Blunami decoders.

I do have a photo of the two decoders side-by-side to show their relative size. As you can see, the 1100 is about the same size as the TSU-1100 so if the TSU will fit the BLU will fit, too. As you can imagine, there is much more room in that 54 foot 4-8-4 tender for the speakers as well when using the 1100 rather than the 2200.

The best thing about having the Blunami decoders installed came about this past weekend when we had a train show. All of a sudden, about an hour before the show was to end, the wifi went wonky and the Engine Driver app that everyone uses on their cell phones stopped working. What that meant was, if you didn't have a Digitrax radio throttle you were done running trains. Unfortunately we were contracted, as it were, to run trains right up until closing time.

I killed the Engine Driver app and pulled up the Blunami app and right away had a pair of trains running. A couple of our other guys had radio throttles, so all four of our NTrak layout tracks were occupied until the end of the show. The 1100 runs just as good as the 2200, sounds just as good, and fits a lot better into smaller spaces.

To say I am pleased with these decoders is an understatement. I have four of these 1100's, two of them have been installed and I plan to replace the two 2200 decoders in the 4-8-4's that have them with 1100's instead.

And then I will have a grand total of four steam 2200's... and I have four HO scale steam locomotives...

I also just purchased a BLU-2200 for EMD diesels, since I have an HO scale GP7.

It looks like my HO scale layout will be DC powered with no blocks. I'll probably use a dedicated 15VDC power supply for it rather than hook any sort of throttle up to it, so it won't even have a control panel, just an on-off switch. I will manually throw turnouts so I won't need power for them, either. That should make things really easy.

And now all I need to do is build some benchwork...
 

Monday, November 3, 2025

Blunami! PT 2.5

 Once upon a time I told you about installing Blunami BLU-2200 decoders into a Bachmann 4-8-4 steamer. As you may recall, I picked the Bachmann 4-8-4 because it has a big tender, big enough to fit this HO scale decoder and the two speakers required for the 2W output power rating of said decoder. At the end of that post, I expressed a hope that they could be downsized for N scale.

Well... someone at Soundtraxx must have been listening, because the BLU-1100 has now been released! 

As soon as I knew they existed, I jumped online and ordered some. Unfortunately they were back-ordered, and even now at the time of this writing they are listed as "out of stock" on Soundtraxx's website.

BUT! I just got an email saying they have been shipped! I should have them in my sweaty paws very soon, and as soon as I do we will have a comparison and another installation post, this time on a Bachmann Class J. 

Tuesday, January 28, 2025

Blunami! Pt II

 In a couple of previous posts I told the tale of the new Soundtraxx Blunami decoders and showed how to install one in an N scale Bachmann 4-8-4 Northern locomotive. I believe the N scale Bachmann J class also has a large enough tender to install a Blunami, so I might try that since I have one of the older versions (but not white-box older; it's one of the 2006 and up releases) that I had to put my own decoder in. I equipped that one with a Soundtraxx TSU-1100 decoder, so there should be enough room... maybe...

But I digress.

In those posts I touched upon the operation of the locos using both the Blunami app and the DCC system, and I was also able to test it using my cell phone as a throttle on the club's DCC system. I have yet to try operating the loco(s) on straight DC, perhaps I will one day but since you can control the loco through the cell phone app on DC it's not really important. The only quibble I had with the Blunami app was there wasn't any way to consist locomotives, not on the Android app at least. 

Well, I'm happy to say that there has been an update to the Android app, and now it is completely possible to consist your Blunami equipped locos on the Blunami Android app. You can't consist non-Blunami locomotives, of course, but I was able to consist both of my Blunami equipped Northerns and run them around my test track using my new-to-me Digitrax Empire Builder DCC set that some sweet lady got me for Christmas. 

And even though I programmed these locos on my NCE set, as I had done with my previous locos, they ran perfectly together... probably because they were identical locomotives (I had a third with a newer type can motor that I matched to the Blunami that was in my installation post; the older motored version got a Digitrax equipped tender) with identical decoders. It's probably a fair bet they won't run with differently branded locos and differently branded decoders until I match them on the Digitrax set, but that's an issue for another day... maybe.

Monday, October 28, 2024

Blunami!

 In my last post I told you about purchasing a couple of Blunami sound decoders and promised an installation article. In this post I'll show you how I put the decoder in a Bachmann 4-8-4 Northern and I'll show you a couple of different options during the installation. There are a lot of pictures, so fair warning, it may load slowly.

First, you are going to need a donor locomotive. I picked the Bachmann Northern because it has a huge 52' tender, and also because I have three of them laying around that I've been able to pick up for good prices, and they are all split-frame versions. However, not all split frame versions are created equal, as I will show you when it comes time to install the locomotive wiring harness.

In addition to the decoder, you are going to need speakers. I picked a couple of ESU 50326 speakers, doubling them up to handle the output power of the decoder's amplifier. I also installed a set of tender pick-ups from Richmond Controls and a TCS six wire micro-connector between the tender and the locomotive. The tender pick-ups make the loco run much better and ensures steady power to the decoder, and the micro-connector makes the installation much easier as well as allowing the tender to be disconnected from the loco for any future maintenance.

Richmond Controls includes installation instructions with their pick-ups, so I don't feel very bad about not documenting them. It's pretty easy, you just have to remember to check your wheel set installations when you put them back in to make sure they are all in the right way. I had one of my wheels reversed and it caused an immediate short circuit when I put the loco on the track.
 


Notice that I installed the two-pin connector that Richmond Controls includes in their kit. For the regular DC installation, the other side of this connector is fastened to the engine, which allows the tender to be unhooked from the engine. In this installation, I connected the other end to the decoder track power wires. 

In my previous installation I mounted the speakers to the tender floor. In that configuration the decoder stays with the tender floor when the shell is removed, so the truck wires are connected directly to the decoder wires. In this installation I mounted the speakers in the tender shell, so the decoder will stay with the shell if it is removed, which is why I chose to use the two-pin plug to allow for the complete removal of the tender floor.

The TCS six-wire plug is also connected to the decoder and the connections are insulated. I used a liquid insulation, but heat shrink would work just as well (and be less messy). TCS provides these connectors in a flat 6 wire plug or in a 2x3 plug, and there is also a flat plug version with black wires (one has a white chaser so it will be connected properly). The black wire version might be better to disguise the connection, the colored wires definitely stand out.

There is plenty of room in the Northern 52' tender shell for the decoder, even though it is intended for HO locomotives. There is plenty of room for the speakers in each end as well, and the entire thing fits right over the weights on the floor. 


Since I was using two speakers they had to be connected together. Soundtraxx cautions against using speakers less than 4 ohms, and each of these speakers are 8 ohms, so I wired them in series. Wiring in parallel would drop the impedance to 4 ohms, so that wasn't an option.



The decoder has plenty of wire for the speakers, so I cut some off to connect the speakers together.. I toyed around with several options when installing the speakers. I thought about mounting them on the forward and aft tender walls pointing inward, but I found there was plenty of room to install them on the top of the shell facing down. Later during testing I discovered that the sound was louder in that configuration than in the previous floor mounted installation.



The six wire plug feeds out of a slot cut in the front of the tender shell and the floor installs with no issues. The harness wiring was tucked underneath the decoder, so the only wiring I had to fight with was the wiring coming from the tender trucks. The screws on the trucks have to be left slightly loose so that the trucks will pivot, the Richmond Controls wipers interfere with the pivot action if the screws are too tight.



And with that done, it was on to installing the other side of the TCS harness on the locomotive.



Both of these locomotives are split frame versions, but as you can see the locomotive on the bottom has a couple of extra screws hiding under the trailing truck.They both run much better than the previous plastic framed version, but the one on the bottom runs slightly better than the one on the top. The biggest difference is in the motors.



As you can see, the top version has the old open sided motor that Bachmann has used for decades. The other version has a nice little can motor that is used on almost all of their newer locomotives tucked inside where it can't be seen. The bottom locomotive had to be completely disassembled to electrically isolate the motor and install the wiring harness, but because the brush caps are exposed on the top locomotive the wiring installation was much easier. The only part that had to be removed on the upper loco was the headlight, to connect the white and blue wires.



The bottom locomotive got holes drilled and tapped for 00-90 screws in each frame half so that brass tabs could be used to connect the track power wires to the locomotive. The Richmond Controls kit includes a neat little bit of double-sided PC board that can be inserted between the frame halves for the wires to be connected to, but I felt this would be a more secure connection.


For the top locomotive, the brass strips that connect the motor to the frame were pulled out of the motor brush covers and wrapped around the frame. The track power wires were then connected to them, and the motor wires were soldered onto the motor brush covers. Care must be taken not to overheat these brush covers, otherwise they may separate from the motor and destroy it. Ask me how I know...

Just a dot of solder on the brush holder is enough to secure the wire. Use of a non-corrosive rosin based flux intended for electronics work is a great help in getting the solder to flow quickly. Under no circumstances should an acid based flux be used! The track power wires are likewise soldered to the brass strips that were formerly connected to the motor brushes.



After the connections are made to the motor and frame a piece of thick styrene can be inserted between the top of the motor and the frame to prevent any inadvertent contact. I cut this piece and test-fitted it before connecting any of the wiring.


The head light holder is secured to the locomotive with a single screw under the leading truck, the same screw that holds the cylinders in place. The bulb holder has to be removed in order to connect the wires from the harness to the bulb.



On the bottom locomotive there was a capacitor installed with the headlight bulb, but on the top loco the bulb wiring was just wrapped around the holder. I opted for an LED on the bottom loco, but I simply soldered the wires directly to the bulb on the top one. There is plenty of room for an LED resistor in the space behind the curved bulb holder. The connections are insulated to prevent contact, and then the holder is reinstalled with its single screw.


There is a plastic piece that the shell screws into that has to be modified for the headlight wiring to pass around. The sides of the screw holder are trimmed back with a sharp hobby knife as shown in the next two photos and the wiring is routed around it, one on each side. 



Notice how the headlight wiring is tucked between the frame halves. The screws that hold the frame halves need to be loosened slightly so the wires can be put into place, then tightened back up.

And with that the wiring is done. Reinstall the shell and connect the connector to the tender, paying attention to the color codes to ensure the connection is correct. Reattach the tender and put it on the track to program.



Using the Blunami app on your phone couldn't be easier. It can be used with either DC (turn the throttle knob all the way up!) or DCC power, and all the speed tables, lighting effects, and other CV's can be programmed either through the app or using your DCC system. You can run multiple locomotives in the app as well, in fact I found it easier to do so that way than on my NCE PowerCab system. I had both of my Blunami locomotives running via the app to speed match them and it was much easier than trying to do it on the Power Cab.

I must say I'm pretty impressed with these decoders, and I certainly hope that SoundTraxx can shrink the size of them in the future so they will fit into more N scale locomotives.



Tuesday, October 22, 2024

Today's Events

 There were a couple of interesting things that happened today.

I installed one of the two Blunami decoders that I bought at Altoona, and I received this car in the mail.
First the car. 
 
This is an NRail Newsletter author's car for 2013, awarded to me from NRail for my article on the restoration of the Cotton Brute in the Jan-Feb 2023 edition. If you are an NRail member, the article is here. I will, of course, be showing this car off whenever I can.

And now for the decoder.
 
It's the relatively new Blunami BLU-2200 decoder from SoundTraxx. I picked up a couple at the N Scale Weekend in Altoona just to see what they were all about. I picked the Bachmann 4-8-4 locomotive pictured above for the installation. Why, you may ask, did I choose this (some would say cheap, I say inexpensive) locomotive for a relatively expensive sound decoder? Simple, it was because of that huge tender. The BLU-2200 is not a small decoder (it is intended for HO or small S scale locos), and so it needs a lot of room, not only for itself but also for the speakers. As to the decoder itself, it is basically a SoundTraxx Tsunami-2 TSU-2200 decoder with bluetooth added, so it has all the sound files and capabilities found on that decoder.
 
I installed a pair of ESU 50326 speakers (the same speaker, incidentally, that was used in the Brute), one in the front of the tender and one in the back, wired in series, to handle the output of the sound decoder. These speakers are rated for 1 watt and the decoder recommends 1.5 to 2 watts (the decoder output is 2 watts), which is why I chose to use a pair of them. The impedance of this setup is 16 ohms instead of 8, but I am hoping this won't end up being an issue for the decoder. There is a warning about using less than 8 ohms, which is why a series connection was used. A TCS 6 wire connector was installed between the loco and the tender so that the two can still be separated.

I didn't take any photos of the installation, so I can't show you how everything went together. However, I do have a second Blunami, as well as a second locomotive, so the next installation will be fully documented. I removed the steel weights inside the tender and replaced them with the cylindrical tungsten weights used on pinewood derby cars to save space, and installed a set of Richmond Controls axle wiper pickups on the tender trucks. The connection to the engine was made by drilling a pair of holes, one in each half of the split frame, and tapping them for 00-90 screws. Brass tabs were installed under the screws so that the decoder track power wires could be soldered to them. This gives power pick ups on six of the eight drivers (two have traction tires) as well as all eight axles (four wheels on each truck) of the tender.

Everything went well, the Blunami sound is excellent as can be expected from SoundTraxx, but unfortunately the headlight doesn't work. I have a feeling the blue wire came disconnected inside the tender, but I haven't opened it up to check yet.* For those of you infected with Bachmann hate you won't believe that this locomotive is a good runner, but with the tender pick ups installed it runs every bit as good as the vaunted Kato Mikado; it's smooth and quiet and never missed a beat over turnouts while I was running it. Everything else works well and I am happy with the installation overall.

I tested it on my DCC system, but I wanted to see what the hype for the wireless operation was all about. I found a quick-start guide on the SoundTraxx website, and a limited amount of information about the Bluetooth app on the BlueRail website. From what I was able to gather, the locomotive can be controlled using pure DC voltage between 6 and 22 VDC just as if it was running on DCC. It can also be controlled wirelessly with a DCC system that does not have a radio control or other wireless option. The quick-start guide says the app is only available for Apple phones, but I was able to find it on Google Play for my Android.

I downloaded the app and, following the Quick Start instructions, I opened the app first. I then turned the layout power on DC, turned the controller all the way up (about 13 volts), and the locomotive sounds came on. The app was then able to locate the decoder and I was able to operate it, with sound and everything, just as if I was using the Engine Driver app with a wireless DCC system. I haven't put a lot of time into the app yet, but from what I've been able to find out you are supposed to be able to program the decoder using the app on DC power. I had already programmed it on the DCC system, so I didn't check this out, but if that is the case that could be very helpful. I didn't check out the wireless operation on DCC, either, but I expect it works just as well.
 
This is a very cool option for the people who have DC on their home layout, are hesitant to install DCC because of the cost, but still want to see what it's all about, or wants to run with a club that is only DCC (as most of them are these days). The decoder itself runs about $170, which, although pricey, is still below a DCC sound-equipped locomotive (starting at $250 or so) plus a DCC starter system (starting at $150 or so for the cheap Bachmann sets, around $200 for the NCE PowerCab or Digitrax Zephyr). Add another $10-15 for the speakers and your initial investment is still less than the price of the cheapest DCC sound-equipped engine, depending on if you have to have the decoder installed by a third party (I'll bet someone in the club will do it for a fair price) or if you have the skill to install it yourself. Plus, if you want to run with your club, you now have a sound equipped locomotive that will run on the DCC club layout using your phone as a throttle. And if after all of that you decide it's not for you, you have a DCC sound equipped engine to sell.

I have read on various forums that, like many DCC decoders, it doesn't play well with PWM DC, but with the PWM throttle turned all the way up (duty cycle 100%) the output is pure DC anyway, so it really didn't affect the operation that I could tell. I didn't try the loco in DC mode, which is disabled as a default setting but can be programmed to be on. Since my home "DC" layout uses a PWM throttle I don't think it would work very well in DC mode, but I do have pure DC throttles I could use to test it if I really decided I needed to. As it stands now, I don't think I really need to.
 
I'm looking forward to playing more with it.

*NOTE: The blue wire did indeed come loose, it has been repaired and the headlight now works like it should.